News

Innovation: Dioxin destruction by CataFlexTM DiOxi catalytic filter bags.

Click on image to open pdf.
Innovation: Dioxin destruction by CataFlexTM DiOxi catalytic filter bags

Dioxin destruction by CataFlexTM DiOxi catalytic filter bags

At a new medical waste incinerator in Thailand, a desire to safely and securely handle dioxin emissions has led to the installation of CataFlexTM DiOxi catalytic filter bags in the beginning of 2018.

Dutch Incinerators, who provides turn-key solutions in thermal waste processing and waste-to-energy, was constructing a medical waste incinerator in Thailand. Based on their extensive experience in the medical and hazardous waste market, they knew that dioxin formation during the combustion process is a challenge. Even when following best practice and using state-of-the-art technology, very little has to deviate for the dioxin formation to end above the very strict regulated limit. Adsorption by activated carbon is the most widely used technology for the capture of dioxins at waste incinerators. However, this technology also has limits, which mean that plant operators and management always doubt whether they are in compliance or not. Online measurements of dioxins are currently not possible, and this means that activated carbon is in practice added in fixed quantities during the operation of the plant. Experience however tells that inlet quantities of dioxins vary significantly, both as a function of the type of waste and the operating conditions of the combustion process. Furthermore, it is also known that increasing the capture of dioxins by increasing the activated carbon injection is not always possible. Dutch Incinerators has previously experienced in an existing plant with similar setup that dioxin emissions could not be pushed below the local regulation of 0.5 ng-TEQ/Nm3 even by dosing 10 times more activated carbon. In fact, the increased activated carbon injection hardly had any effect. On top of this, activated carbon only captures the dioxins and poses a new risk when handling the spent activated carbon – now containing dioxins.

Inlet flue gas specification
Flue gas flow, Nm3/h (wet) 14,220
Flue gas temperature, °C 220
Dioxins/furans, ng-TEQ/Nm3 <6
Dust, mg/Nm3 (wet) <6,000

Dutch Incinerators wanted instead to catalytically destruct the dioxins converting them into primarily CO2 and H2O. This solution became possible by installing CataFlexTM DiOxi catalytic filter bags in their conventional filter house hosting 312 filter bags. The CataFlex™ DiOxi catalytic filter bags work as conventional dust filter bags when it comes to particulate removal, but their fabric is loaded with a proprietary catalyst, which destructs both dioxins and furans. Tests after the installation of CataFlexTM DiOxi filter bags at Dutch Incinerators’ medical waste incinerator showed a destruction of >99% of dioxins and furans without any injection of activated carbon. Inlet and outlet measurements were performed by SGS Thailand Ltd., which confirmed the performance and measured less than 0.02 ng-TEQ/Nm3 of dioxins and furans in the released flue gas – far below the strictest regulations. With the new catalytic filter bags, Dutch Incinerators now has a passive dioxin destruction solution ensuring the plant is always in compliance. This puts the mind at ease and allows for full focus on optimizing plant operation.

If desired, CataFlexTM DiOxi filter bags can also be used in combination with activated carbon injection to ensure the destruction of any potential dioxin or furan that may escape the activated carbon due to offsets in either activated carbon injection or higher dioxin formation in the combustion process caused by some of the upstream equipment. This allow plant operators to optimize the activated carbon injection and still constantly ensure compliance with the strictest regulations.

CataFlex™ DiOxi performance
Dioxins/furans destruction (TEQ) >99%
Dioxins/furans emission, ng-TEQ/Nm3 <0.02
Dust emission, mg/Nm3 (wet) <10
Image_007
Installation of CataFlexTM DiOxi catalytic filter bags in the conventional filter house and tube sheet.

The design of the catalytic filter bags can be customized – in this case, snap rings were used to mount the filter bags to the tube sheet.

Commissioning Emission Report, in compliance!

Another medical waste incinerator was commissioned, this November 2017.

Emission results are in full compliance with any emission regulations world-wide, including the latest EU regulations, by far!

Dutch Incinerators provides turn-key hazardous chemical and medical waste rotary kiln incinerators, in compliance with the most strict emission regulations on the planet.

A new benchmark in company development.

Image of Buddhist prayer ritual
Buddhist prayer ritual

Today Dutch Incinerators celebrated a new benchmark in company development with a Buddhist prayer ritual marking the first day of site construction.

This innovative facility combines medical waste rotary kiln incineration with a waste-to-energy solution, recovering combustion energy for medical waste storage room cooling.

This resulting in a lower electricity consumption of the process, reducing global fossil fuel demand.

Dutch Incinerators celebrates 6 months of successful incinerator operation

Six months of successful operations were celebrated today since the startup of a rotary kiln based medical waste incinerator in Thailand.

After 3 months of operation the plant was inspected in January and since then the incinerator has been in continuous operation ever since, for more than 3 months uninterrupted operation.

Dutch Incinerators designs are characterized by the focus on operational reliability, enabling continuous operation without any planned or unplanned shutdowns for maintenance or cleaning for at least 1 year.

The medical waste incinerator as commissioned in October 2016 has a capacity of 12 tons/day, includes heat recovery for medical waste storage room cooling, stack plume suppression and a dual stage emission control system, based on both dry and wet scrubbing. All emissions are in full compliance with EU and Thai emission regulations.

Dutch Incinerators in the Singapore Straits Times!

Click on image to open pdf.
eco-mastermelt-stfpfc02-h640

Dutch Incinerators designed, delivered and successfully commissioned this month a flue gas treatment facility for the Joint Venture of ECO-Mastermelt PTE-LTD Singapore (EMM), as EPC Supplier.

As partner of this project, the facility built by Dutch Incinerators was presented in a full page advertisement in The Straits Times, the biggest newspaper in Singapore on October 19, 2016.


The flue gas treatment system as installed recovers precious metals from flue gasses produced by precious metal thermal recovery systems of EMM, meanwhile ensuring that the flue gasses emitted to the atmosphere meet the Singapore emission standards.

ECO Special Waste Management is one of Singapore’s leading – if not the largest- waste management companies in the field of hazardous wastes, chemical wastes, solvent recycling, waste water treatment, etc.

Mastermelt LTD is a UK/US based worldwide leader in the recovery of precious metals.